Flexlink Направляющие и опорные салазки (пластик) Монтаж Manuale Utente

Navigare online o scaricare Manuale Utente per Apparecchiature Flexlink Направляющие и опорные салазки (пластик) Монтаж. FlexLink Направляющие и опорные салазки (пластик) Монтаж User Manual [en] [cs] [pl] Manuale Utente

A. Installation of plastic slide rail and support rail 459

X45

XLP

X85

X85P

XKP

X180

X300

FST

XLX

X85X

X180X

X300X

GRX

CSX

ELV

CTL

APX

IDX

Appendixes

A. Installation of plastic slide rail and support rail

About slide rail

The slide rail is attached to the sides of the conveyor

beam to reduce chain friction where the chain would oth-

erwise be in direct contact with the beam profile. It is very

portant that the slide rail is installed properly, so that

the chain can run without disruption.

When the conveyor is to be mounted high above

round level, it might be easier to mount the slide rail onto

a conveyor section while the conveyor beam is still on the

floor. If doing so, leave an extra end, approximately

300 mm longer than the beam, so that it can be cut off

nd adjusted when the beam is finally installed.

Characteristics

Slide rails are available in several materials, each with

dif

ferent characteristics:

The coefficient of friction is normally closer to the lower

alue at startup of a new conveyor. It will increase as the

contact surfaces are wearing in. Lubricants will reduce

the coefficient of friction.

Considerations when selecting slide rail

Each of the slide rails has its own characteristics and is

suitable for different types of applications.

Slide rails made of HDPE or PA-PE are suitable for

st standard applications. PA-PE has higher wear

resistance but should not be used in wet environments.

In environments where high resistance to chemicals

important, PVDF slide rails are recommended.

Hardened steel slide rails in combination

with PVDF

slide rails in bends can be a good combination where

larger particles such as chip occur.

UHMW-PE has the highest wear resistance and can

recommended in applications with accumulation,

transport of heavy parts, high speed, abrasive particles

or requirements on low dust generation.

Horizontal plain bends

The contact pressure between the chain and the slide rail

is v

ery high in the inner bend of horizontal plain bends. It

is important to use the PVDF slide at this location if the

speed is high as there will be increased temperatures

that may cause melting of other slide rails. This, however,

will result in somewhat higher wear on the chain.

1 2 3 4 5 6 7 8

Sommario

Pagina 1 - Appendixes

A. Installation of plastic slide rail and support rail 459POX45XSXLXLPX85X85PXHXKXKPX180X300GRCSXTXCXFXDFSTXLXX85XX180XX300XGRXCSXELVCTLTRAPXIDXAppend

Pagina 2

460 A. Installation of plastic slide rail and support railA. Installation of plastic slide rail and support rail (continued)Example of available slide

Pagina 3 - Joining slide rails

A. Installation of plastic slide rail and support rail 461POX45XSXLXLPX85X85PXHXKXKPX180X300GRCSXTXCXFXDFSTXLXX85XX180XX300XGRXCSXELVCTLTRAPXIDXA. Ins

Pagina 4 - Cutting pliers

462 A. Installation of plastic slide rail and support railA. Installation of plastic slide rail and support rail (continued)Mounting slide rail in whe

Pagina 5 - Anchoring the slide rail

A. Installation of plastic slide rail and support rail 463POX45XSXLXLPX85X85PXHXKXKPX180X300GRCSXTXCXFXDFSTXLXX85XX180XX300XGRXCSXELVCTLTRAPXIDXA. Ins

Pagina 6

464 A. Installation of plastic slide rail and support railA. Installation of plastic slide rail and support rail (continued)Slide rail in conveyor bea

Pagina 7

A. Installation of plastic slide rail and support rail 465POX45XSXLXLPX85X85PXHXKXKPX180X300GRCSXTXCXFXDFSTXLXX85XX180XX300XGRXCSXELVCTLTRAPXIDXA. Ins

Pagina 8

466 A. Installation of plastic slide rail and support railA. Installation of plastic slide rail and support rail (continued)Installation of slide rail